SVC Tire Monitor System Meaning and Fixes

SVC Tire Monitor, also known as Tire Pressure Monitor Sensor (TPMS), is a device that detects changes in the pressure of car tires. The machine lets you know if there’s excessively high or low pressure in your tires.

Causes of SVC Tire Monitor Warning

1. Tire pressure that is too high or too low

Determine the real tire pressure first. If the tire pressure is well outside of the manufacturer’s specifications, the SVC Tire Monitor alarm will show. This alarm typically shows when the temperature is unusually hot or cold. The system will inform you if a tire is overinflated, so don’t guess.

2. The Wrong Wheel

If you replace a wheel on your car, you’ll also need to relocate the tire pressure sensor. Otherwise, the system will be left with nothing to display the SVC Tire Monitor notice in the message center.

3. A tire pressure sensor that isn’t working correctly.

The Tire pressure sensor constantly monitors the pressure of the car tires. This sensor is typically seen inside the wheel of the tire. Although Tire pressure sensors have a long lifespan, their batteries can diminish.

A car as old as ten years is susceptible to sensor failure because of the diminishing battery health. The only way out of this issue is to get a replacement for the sensor.

How To Fix The SVC Tire Monitor Warning in the Chevrolet Silverado.

These sensors first appeared in the 1990s and have been used in a range of vehicles as far back as the first generation of the Chevrolet Silverado 1500.

Step 1:

Your tires may require some air.

  • Tires on our cars are constantly in use, and air can leak out over time, causing tire deflation.
  • If the tire pressure is less than 25 PSI, the tire monitor service light will illuminate immediately.

Step 2:

Reset the TPMS sensors. The tire pressure system should be reset once you complete filling your tires with air, deflating them (in case of excessive PSI), or changing a tire on your vehicle.

Service light resets may be essential when sensor sync is faulty or when sensors are not correctly synchronized.

The service indicator light must be reset using this unique way, despite being unconventional.

  • Place your pickup in park mode and exit the vehicle.
  • While the engine is turned off, turn the ignition key to the RUN position.
  • This position will put the car into reset mode and alert you with two horn sounds before the tire pressure monitor service light begins to flash. Turn the headlight switch on and off four times in three to four seconds to reset the truck.
  • Make use of a car jack to deflate the tires.
  • After deflating the tire for about 10 seconds, you will notice that the horn will sound. After The horn sound stops, re-inflate the tire. After re-inflating the tires, you may have to restart the process. The monitoring system is synchronized with the beeping of the tire sensor.
  • The method must be done for each tire.
  • When the last tire is inflated, the horn will sound twice, signaling the end of the procedure.
  • It’s time to park the vehicle.
  • Using an air compressor, inflate each tire to the desired pressure.
  • When the automobile is operating, the TPMS light should illuminate.

Step 3:

Tire Pressure Monitoring System (TPMS) is an acronym for Tire Pressure Monitoring System. It is a computerized (in most cases) tire inflation valve that measures and transmits the air pressure in each tire to the vehicle’s computer. Replace the TPMS sensors with new ones.

A warning light illuminates when a tire’s inflation pressure falls below the level specified on the sensor, alerting the driver that they have an underinflated tire or tires.

When replacing tires, be careful when removing and reinstalling the sensors. In some situations, sensors can be damaged by usual corrosion, but a careless mechanic can also damage them if they are not removed properly.

How to Fix the SVC Monitor Warning in 2007-2010 Models of the Chevrolet Tahoe

Simply increasing or decreasing the tire pressure can reset your Chevrolet Tahoe’s TPMS without the need for any special tools or equipment.

To get started, follow these instructions: 

  • Switch on the Ignition key without kick-starting the engine
  • Startup your vehicle with its ignition button, if present, without contact with the brake pedal.
  • Simultaneously, press the RKE ( Remote Keyless Entry), the Unlock button, and transmitters lock for 4-5 seconds.
  • Afterward, the car horn would sound twice, and a message displaying “tire learning active” would appear showing the Process of TPMS matching has begun.

How to Fix the SVC Tire Monitor Warning in 2011-2014 Models of the Chevrolet Tahoe

With RKE

  • Switch on the Ignition key without kick-starting the engine.
  • Hold down the RKE (Remote Keyless Entry), transmitters lock and unlock buttons simultaneously until the horn sounds twice.
  • Beginning from the front tire at the driver’s side, place the TPMS Relearn Tool against the tire’s sidewall, close to the valve stem. Afterward, push the button to make the TPMS Sensor active.
  • Run the same process for the passengers’ seat front and rear tires and the driver’s rear tire.
  • After you’ve reset the last tire, turn off the ignition.
  • As recommended on the tire placard, run an adjustment on all four tires.

With DIC Button

  • Switch on the ignition key without starting up the engine
  • Hold down the button showing “Vehicle Information” Until the menu offers the Tire Pressure displays.
  • Maintain Hold on the button until the horn sounds twice
  • Place the TPMS Relearn Tool on the tire sidewall at the valve stem on the driver’s side front tire. Then, to activate the TPMS sensor, press the button.
  • Reset the driver’s side front tire, passenger’s side rear tire, and driver’s side rear tire.
  • Turn off the ignition after you’ve reset the last tire.
  • Ensure that all four tires are properly inflated.

How to reset the SVC Monitor in 2015-2020 Models of the Chevrolet Tahoe.

Base Level Display

  • Switch on the ignition key
  • Wind the Trip knob until the tired menu is displayed.
  • Press and hold the trip knob until the horn sounds twice.
  • Place the TPMS Relearn Tool on the tire sidewall at the valve stem on the driver’s side front tire. Then, to activate the TPMS sensor, press the button.
  • Reset the driver’s side front tire, passenger’s side rear tire, and driver’s side rear tire.
  • After you’ve reset the last tire, turn off the ignition.
  • As recommended, ensure all four tires are inflated.

Uplevel Display

  • While keeping your foot off the brake, depress the “Engine Start/Stop “button for five full seconds.
  • The cluster applications can be accessed by pressing the navigation button.
  • To get more information, click on “Info.
  • Click on the link shown in the tire pressure section.
  • Hold down the button to access the relearn mode
  • Mount the TPMS Relearn against the tire’s sidewall, close to the valve stem to start up this process. As soon as you’re done, push the TPMS Sensor button.
  • Passenger side front tire, passenger side rear tire, and driver side rear tire all need to be inspected and repaired.
  • After resetting the final tire, turn off the vehicle’s engine.
  • All four tires should be inflated to the recommended tire pressure.

Conclusion

It is essential to take note of the changes in the pressure of our care tires. This practice enables early detection of tire pressure problems and makes it easy to address them.

Leave a Comment